Best settings for a Vray Walkthrough Animation

[Dkny2001]

Hello,

i have a question about rendering a animation in Vray.

Should i calculate all the LightCache (all frames) first before i calculate the IrMap or can i calculate every 5-10 Frame? for the Irmap i wrote in the spot3d that is ok to render the irmap every 5-10 frame but what about the LightCache. Sorry if my Question sounds strange...and thanks for anwsers.

And...what are good settings for a nice animation? What about yours?

[mushir_q]

Yes you should always calculate LC for all the frames with flythrough mode.
i am not sure about subdivision but 500-1000 would be sufficient.

then calculate Ir map with nth frame rate.
Nth frame rate depends on how fast your camera is moving or jumping to another frame.
you can use low preset for IR.

if your camera is quite slow then you can keep 15-25. if its fast then you can go with 5-10 to be on a safer side ..

Always use area or video filter . catmul might cause flickering.

I hope it helps..

[Dkny2001]

Thank you very much for your anwser...that was the right anwsers to my questions...thanks i´ll tried it this way !

Greetings :-)

[fareenfarid]

the light cache calculate all the frames in the scene's timeline. It ignores the nth frame .
So if your animation is 500 frames and your time line is set to 1000 frames it will calculate for the 1000 frames
By the way in the sp1 and 2 you dont have to render the light cache and ir seperately. it automaticaly calculates the light cache first and then uses it for the ir

[Dkny2001]

hello.
thank you fareenfarid for your anwser.that means that i can start to calculate my lightcache and IR map together and at the end of calculating i can start my rendering from file.

thanks

[Dkny2001]

Hello.
If i have calculate all (irmap+lc) what settings should i make for rendering then? High quallity Irmap settings and Lichtcache or it doesnt matter?
thx

[kamaraj]

i have a question about rendering a animation in Vray. walkthrough

[PONNU]

pls sent vray walkthrough setting this mail id... kanmani.friends@gmail.com..

thanks,

[Visu3x]

can you send me a vray setting for animation... saving an ir and Lc, and setting for vray final animation,
here is my email visu3x@yahoo.com thankss

[raghu n]

Hi, getting flickering in my walkthrough scenes. am using v-ray in 3d max. and what r the good settings for exterior walkthrough.(3d@mediapulsetech.com)

[farrokh]

I have the same problem if you help me I would be so pleased. f.rostamikia@polyviz.com

[moxy]

pls sent vray walkthrough setting this mail id mohit.animator@yahoo.com

thanx :-)

[sily22]

I love to know the setting for vray walkthrough also, been struggling for it.
Could you please send it to my email sily22@gmail.com. Appreciate it alot. Thank you.

[matsam]

plzzzzzz send me vray walk through settings its urgent otherwise i am die....(

[suresh6]

could anyone send me a walkthrough setting with vray to this mail id...
sureshbabu002@gmail.com...

Thanks

[justonly]

i have a question about rendering a animation in Vray. walkthrough pls sent vray walkthrough setting this mail id...justonly@rediffmail.com


Thanks

[alikolbakir]

can anyone send to me walkthrough settings for vray... i need this so much..
my mail is alikolbakir@gmail.com
thanks all for help...

[brijeshkumarrana]

pls sent vray walkthrough setting this mail id... brijeshkumarrana@gmail.com..

thanks,

[jolek291]

pls sent vray walkthrough setting this mai
jolek291@gmail.com
thanks a lot :3

[doolcy]

pls sent vray walkthrough setting this mail id... ismail_bakkar@yahoo.com..

thanks,